Boot.ini all versions download

When Windows NT all versions is installed, you will note that the boot loader always provides for a boot into the operating system with a plain vanilla VGA driver, thus a VGA compatible display device is one of the basic requirements of all Windows NT installations.

A typical situation might involve updating your current display driver, or possibly installing a new video card with new drivers only to start the machine and find out the new driver version doesn't work correctly with your hardware. Obviously it's very difficult to fix problems when nothing appears on the video screen. In the sample BOOT. In most cases, this will enable you to reboot and then fix an incorrect or improperly working display driver.

Does your system hang during boot? As windows NT starts, you have probably noticed the series of dots that transverses the screen during the startup process.

In Windows , the startup bar that moves across the screen indicates the same thing. In Windows NT, each of these dots, and in Windows , each block within the startup bar, represents a driver or service that the boot process is loading. If, during the boot process, the system hangs during this phase, how could you possibly know which driver or service has caused the hang? By using this switch, the boot process will list the name of each driver on the screen as it begins to load.

If the boot hangs during the boot process, either the last driver or service name listed or the next driver or service in order is causing the hang. To find the order in which drivers and services are being loaded, check in the following system registry location:.

Disabling serial mouse detection During the boot process Windows NT attempts to detect a serial mouse on any active serial port in the system, which can cause problems with certain serial devices. A problem often occurs with some Un-interruptable Power Supply's UPS that monitor or control the system via a serial port. The detection signal intended to find the mouse causes the UPS to shut down and sometimes the computer with it.

Many other serial devices also could have undesirable responses to this signal, such as external modem devices. This switch has several forms.

Of course, you can choose any COM port here. Again, you can use any list of COM ports here. Microsoft's Windows NT documentation and yes too says this switch is useful when you are troubleshooting memory problems, such as parity errors. There is, however, a better use for this switch, such as when testing applications for compatibility on systems with a minimum amounts of physical memory.

If you are a serious computer user, you probably have at least 64MB to MB of physical memory in your machine. Supporting system debugging, including remote In Windows NT you have the option of loading a debugging tool at boot time and along with it enable a serial port for debug purposes, thereby creating a debugging terminal. You can even connect this debug terminal to another machine via a modem and dial-up connection, which would allow a support person to dial in and debug system problems remotely.

This is the default and is typically not explicitly used in BOOT. By default, the debugger attaches itself to the last, or highest numbered, COM port on the system. If it detects a modem on that port, it sets the baud rate on the port to , otherwise, it selects as the baud rate and assumes a null-modem cable connection to a terminal. This switch loads the debugger code but doesn't activate it unless a Kernel error occurs. Differences in Boot Menus [ Back ]. If you've been using Windows NT 4.

You can also view and change some boot options in Control Panel under System. Because this functionality is limited, it is not discussed in this section. Bootcfg is a command-line tool that can edit boot options on local and remote computers. Using the same Bootcfg commands and procedures, you can edit Boot. You can use Bootcfg to add, delete, and change all boot entry parameters and boot options; however, you cannot use it to set an indefinite boot time-out value.

You can also use Bootcfg commands in a script or batch file to set boot options or to reset them after you replace or upgrade an operating system. Unlike manual editing, Bootcfg edits boot options without changing the protective attributes on Boot. It also helps you avoid typing errors that might prevent the operating system from starting.

You must be a member of the Administrators group on the computer to use Bootcfg. For a list of boot parameters that are relevant to driver testing and debugging, see Boot. You can have multiple boot entries for the same operating system, each with a different set of boot parameters. Windows creates a standard boot entry when you install the operating system, and you can create additional, customized entries for an operating system by editing Boot.

Skip to main content. This browser is no longer supported. Download Microsoft Edge More info. Contents Exit focus mode. Overview of the Boot. If you try booting these systems using BOOT. BAK and boot. BAK files, and these lines added to the new boot. INI file that you're allowed to change from this dialog box: 1 You can select the default OS to boot up, and 2 How many seconds to display the boot menu. INI file! INI file on your own for further editing; such as arranging the order in which the OS selections appear in the menu.

So, if you decide to delete the new OS, simply set your old OS as the default boot OS and uncheck the item for displaying the menu list or manually set it to zero; same result. You could then safely delete the new OS partition, but not the files it added to your old partition. INI file in that partition's root directory. This is how it determines which of several possible BOOT. INI files on a system it should open for editing.

Then, without rebooting! INI file from the root directory of the other partition! And finally, 4 Do a quick check of the file's attributes to make sure they're still 'Hidden, System' the 'Read-only' attribute is not required. In this case, we have to assume for now that you deleted a critical component. Write down any error messages you see on the screen when trying to boot up your computer!